As you may have noticed, we recently switched our domain to emphasize our non-profit status as a part of Extraordinary Education. So when visitors type the old .com domain, they will now be automatically directed to our new themakerbarn.org domain and website. In addition to the change in domain, we also moved from a hosted WordPress solution to a full service website hosting solution. That change will give us a great deal of flexibility in terms of the services we can offer through our website. We have future plans for a member forum and a wiki. All in all the process was pretty painless and went forward without any major glitches. Hopefully I’m not jinxing us by writing this!
The Hegner Scroll Saw We’ve been watching school and government auctions for items to equip The MakerBarn. We have gotten some great deals on high quality tables, cabinets, and chairs. On one of the auctions sites, I noticed a school district down near Victoria was auctioning a Multimax scroll saw and a Delta bandsaw. Both looked fairly rough, but I placed some bids just to see how it went. Victoria is a long drive so I hoped by bids would be fruitful. I won both auctions. This meant driving 300 miles, but with luck, it would be well worth it. The Delta bandsaw was fairly recent vintage. It had been the victim of a student brawl and had been knocked over. But the upper and lower trunions were broken, but everything else survived. A few used parts off eBay and some new tires, and the bandsaw tuned up beautifully. The … Read More
Thanks goes to Ed Draper for getting us a booth at The Woodworking Show. The Woodworking Show is a nationwide show that visits the Houston area once a year. We had people from as far away as Austin and San Antonio visit the booth and learn about makerspaces and The MakerBarn. There were several woodworkers from our area who said they were very happy to hear about us and would come by for a visit.
We aren’t all woodworking and machine shop; we also have a wonderful electronics lab in the works. The lab centers around four tech stations. Three of the stations will be configured for experiments and testing audio and other low frequency work including micro-controllers. You could use one of these stations to work on anything from tube amplifiers to Arduinos. The forth station is equipped for work with RF (Radio Frequency) devices. If you are into Ham Radio, this will be your favorite workspace. Ever wonder what the spectral output of you WiFi router looks like? The 9594E cover spectrum up to 2.9GHz. The normal tech stations will each be equipped with a Tektronix 2246 100MHz oscilloscope, BK Precision 5MHz Function Generator, lab multimeter, and power supplies. The RF station will have an HP8640B signal generator, an HP 8594E Spectrum Analyzer, and an HP 5328A frequency counter. All tech stations will … Read More
Today marked a major waypoint in the building of The MakerBarn. The upstairs fur downs are framed out, which marks the end of all the framing work. The fur downs are structures that drop down the ceiling to hide A/C ducts, beams, and plumbing. In our case we were covering the roof support beams that run the length of the building. The beams were, well, ugly and crooked. A little 2×4 orthodontia, and the ceiling will look fine. Next is completing the electrical for lighting, install the insulation, then hang sheetrock. Start getting those party hats ready for grand opening!
We just finished refurbishing the Roll-In Metal Cutting Band Saw. This saw was donated to The MakerBarn. It was in pretty rough shape because it had been sitting in a storage warehouse for many years. The machine was stripped down to nuts and bolts. Bearings were replaced. Paint was stripped and repainted. A few parts had to be fabricated, and the rubber tires were replaced. The vise needed quite a bit of machine work, but it too came out fine. The motor was rebuilt, and new electrics installed. The machine even has MakerBarn’s MACS system installed for safety. It’s all ready for some metal cutting action!
We picked up the SawStop table saw today. This will be the jewel of our woodworking shop. It is a SawStop 3HP Industrial Series saw with a 52″ fence. This is SawStop’s top-of-the-line machine, and we were fortunate, with the help of Madera Works of Texas, to become its new owners. It’s a big saw, almost 8′ wide. The photo shows it just after we unloaded it. There are support legs for the extension table which are not yet installed. This saw should serve us for many years to come.